收藏本站
W25Q128BV
7.2.15 Fast Read Quad I/O (EBh)
The Fast Read Quad I/O (EBh) instruction is similar to the Fast Read Dual I/O (BBh) instruction except
that address and data bits are input and output through four pins IO 0 , IO 1 , IO 2 and IO 3 and four Dummy
clock are required prior to the data output . The Quad I/O dramatically reduces instruction overhead
allowing faster random access for code execution (XIP) directly from the Quad SPI. The Quad Enable bit
(QE) of Status Register-2 must be set to enable the Fast Read Quad I/O Instruction.
Fast Read Quad I/O with “Continuous Read Mode”
The Fast Read Quad I/O instruction can further reduce instruction overhead through setting the
“Continuous Read Mode” bits (M7 -0) after the input Address bits (A23-0), as shown in Figure 14a. The
upper nibble of the (M7-4) controls the length of the next Fast Read Quad I/O instruction through the
inclusion or exclusion of the first byte instruction code. The lower nibble bits of the (M3- 0) are don’t care
(“x”). However, the IO pins should be high -impedance prior to the falling edge of the first data out clock.
If the “Continuous Read Mode ” bits M5-4 = (1,0), then the next Fast Read Quad I/O instruction (after /CS
is raised and then lowered) does not require the EBh instruction code, as shown in Figure 14b. This
reduces the instruction sequence by eight clocks and allows the Read address to be immediately entered
after /CS is asserted low. If the “Continuous Read Mode ” bits M5-4 do not equal to (1,0), the next
instruction (after /CS is raised and then lowered) requires the first byte instruction code, thus returning to
normal operation. A “Continuous Read Mode” Reset instruction can also be used to reset (M7 -0) before
issuing normal instructions (See 7.2.20 for detail descriptions).
/CS
Mode 3
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
CLK
Mode 0
Instruction (EBh)
A23-16
A15-8
A7-0
M7-0
Dummy
Dummy
IOs switch from
Input to Output
IO 0
IO 1
IO 2
IO 3
20
21
22
23
16
17
18
19
12
13
14
15
8
9
10
11
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
Byte 1
Byte 2
Byte 3
Figure 14a. Fast Read Quad I/O Instruction Sequence (Initial instruction or previous M5-4 ? 10)
- 32 -
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
W25Q16BVSFIG IC SPI FLASH 16MBIT 16SOIC
W25Q16CVSFIG IC SPI FLASH 16MBIT 16SOIC
W25Q16DWSFIG IC FLASH SPI 16MBIT 16SOIC
W25Q16VSFIG IC FLASH 16MBIT 80MHZ 16SOIC
W25Q32BVZPIG IC SPI FLASH 32MBIT 8WSON
W25Q32DWZEIG IC FLASH SPI 32MBIT 8WSON
W25Q40BWSSIG IC FLASH SPI 4MBIT 8SOIC
W25Q40BWZPIG IC FLASH SPI 4MBIT 8WSON
相关代理商/技术参数
W25Q128BVEIG TR 制造商:Winbond Electronics Corp 功能描述:SPIFLASH, 128M-BIT, 4KB UNIFOR
W25Q128BVEIP 制造商:WINBOND 制造商全称:Winbond 功能描述:3V 128M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI
W25Q128BVFIG 制造商:Winbond Electronics Corp 功能描述:Flash Serial-SPI 3.3V 128Mbit 16M x 8bit 8.5ns 16-Pin SOIC 制造商:Winbond Electronics Corp 功能描述:128MB SPI FLASH
W25Q128BVFIP 制造商:WINBOND 制造商全称:Winbond 功能描述:3V 128M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI
W25Q128FV 制造商:WINBOND 制造商全称:Winbond 功能描述:SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q128FVAIG 制造商:WINBOND 制造商全称:Winbond 功能描述:3V 128M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q128FVAIP 制造商:WINBOND 制造商全称:Winbond 功能描述:3V 128M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q128FVAIQ 制造商:WINBOND 制造商全称:Winbond 功能描述:3V 128M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI